The Captician X Dre616 - Cap visor Materials/ How to clean your cap visor.
Knowing if your baseball cap visor is made from cardboard or plastic is crucial for looking after your caps. This helps you to choose the best method to clean and curve your visor, without damage.
Surprisingly, there isn't much information on the net on how to identify the material of your visor and how to safely clean them. When we partnered with Dre616, we knew this topic would be perfect for him to tackle.
Doug's video and this blog will take an in-depth look into this topic, so you can keep your caps in top condition.
Cap visors - Back to basics
The fundamental rule of visor care is not to get it completely soaked by submerging it in water, especially if you’re unsure of the visor material.
Doing so can lead to it warping and becoming soggy. If you're cleaning or steaming to curve the visor, you will naturally expose it to moisture. This is okay, as long as you don’t over-wet or over-steam it.
A lot of the old vintage caps used cardboard. Modern visor materials tend to be more water-resistant, but following the non-soak rule is best. Over-wetting the visor may cause the water to spread out into other areas of the cap, such as the crown. The crown is reinforced with a coated material called buckram, regularly getting this wet can cause your cap to lose its shape.
Different types of cap visor materials
Cardboard, known as paperboard, was a long-time visor ingredient in vintage baseball caps. Economical and easy to use, the earliest baseball caps were all made with some variation of this material. It’s also handy to note that many reissues or heritage reproductions of prior historical caps now almost always use plastic, for the benefits of durability.
Most baseball cap manufacturers now use plastic visors made from high-density polyethylene (HDPE). The visors are die-cut into the shape using flat sheets of this plastic. Curved brims are then heat-molded into shape. Some manufacturers use a ‘foamed’ plastic visor. This is done by putting a little bit of air into the material to create a hard foam. This can be more cost-effective than using pure plastic. This foamed version still has the same water-resistant qualities as the un-foamed plastic visors.
Resin fibre blend
The last category is the one now favoured by New Era. It’s referred to as a resin fibre blend. This is a mix of plastic and cardboard, and it provides the best properties of both. The cardboard fibre gives it a bit more softness, flexibility, and shape memory, whilst the plastic provides the toughness and durability that you get from a plastic visor. This has been used frequently in New Era's caps for over 20 years.
How to know what visor material is in your baseball cap.
Now that you know about the different materials, how can you tell what's visor materials are used in your cap collection? Here are a few ways that you can tell.
The feel of the visor is a major indicator. Give your cap a slight flex and see how it reacts. If it's plastic it's going to spring back fairly quickly to any flexing movements. By comparison, cardboard is going to 'give' a lot quicker and may not be so resilient in springing back to shape.
The second thing to look for is the shape memory of the material. Doug and I have found that with plastic visors, you need to flex them before each time you wear them.
Despite steam curving it, plastic tends to lose its shape faster over time, in comparison to the plastic fiber blend.
The mixed visor retains the shape a lot better than the pure plastic one. I find it always tries to spring back to its flat condition.
You can also tell by the brand of the baseball cap. As previously mentioned, New Era has been using the plastic and fibre blend for 20 plus years. It seems that other brands have followed suit. 47 Brand, Mitchell and Ness, Supreme all use some variation of a plastic visor.
Even vintage baseball cap manufacturer Ebbets Field Flannels mainly use plastic. The only caps that they produce with cardboard visors are the limited soft visor range, which is clearly labeled.
The standard New Era plastic and cardboard blend doesn’t spring back as forcefully as plastic does. You don’t have to steam this visor quite as long as you would a pure plastic visor.
47 Brand’s plastic visor has a sharper sound when you tap on it. It will also spring back a little bit more forcefully when you try and flex it. The pure plastic visor has a higher softening temperature – you can leave them in the steam just a few seconds longer than a standard New Era cap.
A completely soft visor, as shown in the gif, makes a dull sound when you tap it. You can see by how easily its cardboard visor flexes and moves around.
Cleaning cap visors
As mentioned before, you don’t want to soak or submerge the visor even if you know for sure it's all plastic or the plastic fibre blend.
Because the visor is the most handled and exposed area of the cap, this often gets dirty very quickly. It's okay to consider using a fabric protectant on the visor. This will help to stop water from penetrating the visor. It will also make it easier to clean.
Brushing is the best way to routinely keep your visor clean. Be sure to pay particular attention to the crevice between the visor and the crown of the cap. That tends to be a magnet for dirt and debris.
How to steam curve your visor
If you like to wear your caps with a curve and the visor contains plastic, then it is recommended to always heat the visor with steam. Click here to see Doug’s curving video tutorial.
When the material is warm and pliable you're avoiding creating small or large cracks in the material. If you bend the visor whilst it’s cold, it fatigues the material and creates, a lot of cracks so over time. It will lose its stiffness and the ability to hold shape. In extreme cases the visor can snap completely.
Storage - How to protect your visors
Storing your baseball caps in a safe place is essential to keeping them in ready-to-wear condition, whether it's in bin storage, a cap carrier, or inside your closet on a shelf. The main goal is to keep it away from dust and accidental spillages.
We hope this has helped you to determine the material of your visors, how to safely achieve a curve, and care for your caps. To watch the full episode, click HERE.
CLEAN AND RESTORE WITHOUT DAMAGE
This is the first in a series of cap care videos and blogs with the legendary Doug, from the Dre616 YouTube channel. Brushing is an important and quick cap maintenance task that prevents dust, lint, hair and soil particles from building up on your cap. When left on the fabric, they can become ingrained and attract more dirt. Meaning you will have to clean it more often. Brushing your cap after each use and storing it away will keep it looking its best for longer.
It can be hard to know what is the best way is to clean your caps without ruining them. From my experience as a professional cap restorer, I will walk you through the pros and cons of doing so.
Have you ruined or thrown away caps from D.I.Y methods gone wrong? Even if you've tried and been unsuccessful in the past we got this! I understand your pain. Back in the day, I destroyed countless caps experimenting with stain removal methods. It's why I'm sharing with you all of my previously secret cap cleaning tips